All Products (8905)

Audio Control LC2i 2 Channel Line Out Converter Accubass and Subwoofer Control for amps to your factory system & ACR-1 Dash Remote The LC2i is a compact, two-channel processor with active input circuitry. It can accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers. It converts them to high-quality pre-amp signals that can be directed to after-market processors and amplifiers. Users can enjoy maximum sound quality using factory volume and steering wheel controls. General Features: Two channels of active speaker-level inputs - Accepts 400-watt signals per channel. AccuBASS processing for correction of bass roll-off Fixed and variable outputs with discrete-level controls GTO - Signal sensing inputs The 12-Volt trigger that will turn on LC2i Dual amplifier 9.5-volt pre-amp outs Level matching controls 12 Volt trigger output Input for optional subwoofer level control: AudioControl ACR-1 Dimensions: 6-3/8"W x 3-1/8"D x 1-1/2"H Authorized Internet Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) The LC2i Specifications Maximum speaker level input: 400 watts per channel Maximum Preamp Output: 9.5Vrms / 13V peak Optional Dash Level Control Remote: +0dB / -19dB Frequency response: 10 Hz - 100,000 Hz; ±1dB Total harmonic distortion: 0.01% Signal to Noise ratio: >110dB Input Impedance: 20K ohms Output Impedance: 150 ohms Power draw: 150 mA Recommended fuse rating: 1 Amp Weight: 1 pound What's in the box: Two-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC2i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors General Features Wired Remote Level Control Mounts on the dash using the built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Audio Control LC6i 6 Channel Line Out Converter with Internal Summing for adding aftermarket amps to a factory system & ACR-1 Dash Remote AudioControl continues to simplify OEM integration with the new LC6i Six Channel Line Output Converter with internal summing. The LC6i is built on the same technology as its predecessor, the LC6. The LC6i converts speaker-level inputs from a factory radio or factory amplifier into high-quality pre-amp signals. The addition of internal summing capabilities and improved GTO™ signal-sense turn-on make the LC6i the perfect way to solve your OEM headaches. The LC6i allows for the addition of aftermarket processors and amplifiers while maintaining the use of the factory volume and steering wheel controls. Internal signal summing and AudioControl’s new GTO™ signal-sense turn-on make the LC6i a perfect OEM interface for a performance audio system. The LC6i follows in the steps of the rampantly successful LC8 Eight Channel Line Output Converter, offering all the same features for 6-channel systems at a reduced price. The LC6i accepts speaker-level signals, both crossed-over and full range, and converts them to high-quality pre-amp signals. Signals from factory radios with built-in crossovers can be overcome by summing them together internally to provide a full-range preamp signal. The LC6i provides the type of clean pre-amp signals installers are familiar with. Those who desire custom control over the sound can easily add one of AudioControl’s many crossovers or equalizers, which offer unlimited system design flexibility that is different from traditional OEM interfaces. Add remote-level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. It comes with a 20-foot cable and removable mounting enclosure (for custom dash installations). General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.5 lbs Size: 8.00" W x 6.00" D x 1.20" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC6i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 9.5Vrms Output gain: +/-12 dB Frequency response: 10Hz-22kHz Total harmonic distortion: 0.01% Input Impedance: 20K Ohms Power supply: High headroom PWM switching Power draw: 200mA Recommended fuse rating: 1 Amp Remote Trigger Output Current: 1 Amp What is in the LC6i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC6i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote-level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. It comes with a 20-foot cable and removable mounting enclosure (for custom dash installations). General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Audio Control LC7i, 6 Channel Line Out Converter with bass restoration, adds aftermarket subs and amps to a factory system & ACR-1 Dash Remote. The AudioControl LC7i, a six-channel active line converter, allows music lovers who want a great in-car audio experience to keep their factory-installed source unit and dramatically improve their system performance. The LC7i delivers amazing sound quality and fixes one of the biggest letdowns of today’s factory systems: weak bass! Designed for maximum sound quality and enhanced audio performance, the LC7i incorporates AccuBASS™. This patented process automatically corrects for the bass roll-off that is common with many factory-installed audio systems. AudioControl’s unique and exclusive AccuBASS™ circuitry maintains and restores the Bass as the volume increases, improving the audio performance. The LC7i allows the flexibility of powering the audio signals downstream to single or multiple factory amps maximizing sound quality & achieving high output at a great price. In addition, the LC7i is designed to fit into a compact chassis allowing an easy & flexible factory system upgrade in today’s space constrained vehicles. The ACR-1 dash remote (sold separately) allows the user to control the level of the low-frequency output. Add remote-level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. It comes with a 20-foot cable and removable mounting enclosure (for custom dash installations). General Features: Six Input and Output Channels 6 Speaker Level Inputs - Can Accept 400-Watt Signals! Signal sensing inputs GTO (Great Turn-On) Circuit Internal Channel Summing AutoMode inputs Level matching controls 12-volt trigger output Line Output Converter: A device for converting a powered (or amplified) signal into a pre-amp line level (or non-powered) signal Input for optional subwoofer level control: AudioControl ACR-1 Color: Black Weight: 3.0 lbs Size: 7.5" W x 4.72" D x 1.22" H Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) LC7i Specifications: Maximum speaker-level input: 400 watts @ 4 ohms Maximum output level: 8.5Vrms Output gain: ±15 dB Frequency response: 10Hz - 22,000 Hz Total harmonic distortion: 0.01% Input Impedance: 20 Kohms Output Impedance: 150 ohms Power supply: High headroom PWM switching Power draw: 350mA Recommended fuse rating: 2 Amp Remote Trigger Output Current: 1 Amp What is in the LC7i box: 6-Channel line-output converter Instructions/Specs/Warranty (on packaging) Quality Control Certificate AudioControl LC7i owner's manual AudioControl Remote ACR-1 Dash Mount Wired Remote Level Control for Select AudioControl Sound Processors Add remote-level control for your AudioControl processor or amplifier. This is the replacement remote for the Epicenter. It comes with a 20-foot cable and removable mounting enclosure (for custom dash installations). General Features Wired Remote Level Control Mounts on the dash using built-in bracket Detachable mounting plate Works with select AudioControl sound processors Direct replacement remote for the Epicenter Includes 20' power cable Authorized Dealer 5 Year Manufacturer's Warranty (*when installed by an authorized AudioControl dealer) compatible with 6XS ACM-1.300 The Epicenter® Concert Series LC2i LC6i LC7i Overdrive Plus Matrix Plus LC-4.800 LC-6.1200 legacy products supported LC6 LC8 Original Epicenter® (bypass not supported) What is in the ACR-1 box: Remote dash mount control 20' RJ-14 cable. Mounting Instructions on packaging AudioControl ACR-1 owner's manual Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-ohm load. The Class-BD technology produces bass more efficiently than traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 channel  RMS Power Rating: 2 ohms: 300 watts x 1 channel RMS Power Rating: 1 ohm: 500 watts x 1 channel CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilizes 1% tight tolerances, improving the circuit's efficiency and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box? Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate R2-200X2 Prime Series 2-channel car amplifier 50 watts RMS x 2 Give your speakers the power they deserveRockford Fosgate's Prime Series R2-200X2 amplifier can power two speakers with 50 watts RMS each, so you'll hear your music clearly over the noises of the wind and road. You could also use this amp in bridged, 1-channel mode to power a subwoofer with up to 200 watts RMS. High- and low-pass filters help you get maximum performance from the speakers in your vehicle. Setting it up for optimum performanceRockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It's a simple system to use — turn it up until the light shows red, then turn it down until the red light goes out. Speaker-level inputs let you hook this amp up to almost any system, even a factory stereo. Product highlights: 2-channel car amplifier 50 watts RMS x 2 at 4 ohms 100 watts RMS x 2 at 2 ohms 200 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode) CTA-2006 compliant Class-D amplifier design variable high- and low-pass filters (50-250 Hz, 12 dB/octave) More Info: C.L.E.A.N. gain setup system includes clip lights auto remote turn-on preamp and speaker-level inputs preamp outputs wiring, fuse, and hardware not included with amplifier 4-gauge power and ground leads and a 30-amp fuse recommended dimensions: 8-1/8"W x 2"H x 7-3/4"D warranty: 1 year Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate R2-300X4 Prime Series 300 Watts 4-Channel Class D Amplifier Primed for performance, the R2-300X4 is a 300-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology, which reduces the vehicle's electrical system demand. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. General Features: Rockford Fosgate Prime R2-300X4 Class-D Full-Range 4-Channel Amplifier 50 watts RMS x 4 at 4 ohms 75 watts RMS x 4 at 2 ohms 150 watts RMS x 2 bridged output at 4 ohms bridged mode Total power output: 3000 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeat able Auto Turn-On Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable on-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Full Range Class D Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers 1 Year Warranty Low level: 125mV-5V High level: 250mV-10V Frequency Response: 20 Hz - 20 kHz Hz Total Harmonic Distortion (THD): <1% Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250 Hz, 24 dB/octave Recommended Fuse Rating: 60A Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-300X4 package: R2-300X4 Owner's Manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance Rockford Fosgate contact information ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Rockford Fosgate Prime R2-500X4 500W Prime Series 4-Channel Full Range Class D Amplifier Primed for performance, the R2-500X4 is a 500-watt, full-range Class-D amplifier capable of operating at 4Ω or 2Ω stereo and 4Ω bridged/mono. This amplifier is extremely efficient because of its Class-D technology which reduces demand on the vehicle's electrical system. The amp also features C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. supply that generates more power as voltage increases. Rockford Fosgate's R2 amplifiers are the building blocks for great audio systems, powerful enough to even DRIVE our Punch speakers and subwoofers. They have undergone an amazing upgrade by packing them with the latest features at an incredible value. Best of all, they are designed and engineered here in Tempe, Arizona. General Features: Rockford Fosgate Prime R2-500X4 RMS Power Rating: 4 ohms: 75 watts x 4 Channel RMS Power Rating: 2 ohms: 125 watts x 4 Channel Bridged, 4 ohms: 250 watts x 2 Channel Total power output: 500 watts Balanced Differential Inputs with RCA Pass Through Outputs High-Level Input Capable Defeatable Auto Turn on Circuit Features C.L.E.A.N. Set-up 2/4 Channel Input Selection Switch Front and Rear Variable Input Gain adjustment level Continuously Variable On-Board Punch EQ Top Mounted Control Panel Short Circuit & Over Current Protection CEA-2006 Compliant & CE Compliant Rollback Protection Fully Adjustable 12 dB/octave High and Low pass Butterworth Crossovers Frequency Response: 20 Hz - 20 kHz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: xx dB Variable high-pass filter: 50 - 250 Hz, 24 dB/octave Variable low-pass filter: 50 - 250Hz, 24 dB/octave Recommended Fuse Rating: 80A 4-gauge power and ground wiring are recommended for installation Dimensions: 1.9" x "6.8" x "10.1" Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the R2-500X4 package: R2-500X4 owner's manual 4-Channel amplifier Two 7" Speaker input harnesses 3mm Allen Hex key Four 3/4" Screws 4 Flat washers Installation and Operation Instructions Certificate of Performance ⚠️Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca

Rockford Fosgate Punch P500X1BD 500W RMS Punch Series Monoblock Class D Car Power Amplifier The Punch P500X1bd is a mono amplifier capable of 500 Watts into a 1-ohm load. The Class-BD technology produces bass more efficiently than traditional amps, and its frequency response allows it to be optimized for subwoofers. General Features: Punch BD Series Monoblock Class BD Car Amplifier RMS Power Rating: 4 ohms: 150 watts x 1 channel  RMS Power Rating: 2 ohms: 300 watts x 1 channel RMS Power Rating: 1 ohm: 500 watts x 1 channel CEA-2006 compliant amplifier MOSFET power supply Muted turn-on. Cast aluminum heatsink. 12dB/octave Butterworth crossover Stealth top-mounted control panel LED power, thermal, and protection indicators. Nickel-plated captive C-clamp terminals. Ultra-efficient Class BD circuitry to maximize amplifier power efficiency. On-board differential inputs eliminate noise picked up by the signal cable. Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator) High-level input capable with Auto Turn-On circuit (RFIF2SW required, sold separately) MESHA3 reduces MOSFET temperatures, lowers distortion, increases durability, and prolongs the output device life span. Built-in NOMAD is a "real-time" analog computer that protects your amplifier from shorting speaker wires and dangerously low speaker impedances. Cast aluminum convection heatsink with DTM (Dynamic Thermal Management) evenly distributes excess heat across the entire amplifier heatsink to efficiently keep the amplifier temperatures low. DSM (Discrete Surface Mounted Components) utilizes 1% tight tolerances, improving the circuit's efficiency and lowering the operating temperature and potential for noise-like circuit boards designed by aerospace manufacturers. Input sensitivity: 150mV - 12V On-board Punch EQ with +18dB boost @ 45Hz. Variable low-pass filter: 50-250 Hz Selectable infrasonic filter: off / 28 Hz Frequency response: 20 - 250 Hz Total Harmonic Distortion: <1.0% Dimensions: 11"L x 7-3/4"W x 2-3/8"H 8 AWG to 18 AWG speaker wire output terminals Authorized Internet Dealer 1-year Manufacturer's Warranty What is in the P500X1bd box? Mono subwoofer amplifier Four 1-1/2" Self-tapping screws 2.5mm Allen wrench Quick setup instructions Certificate of Performance P500X1bd owner's manual Warning:This product can expose you to chemicals known to the State of California to cause cancer. For more information, go to P65Warnings.ca.

Cerwin Vega VPAS12 600W Max (250W RMS) 12" Under Seat Powered Subwoofer Enclosure Slim Powered Enclosure This ultra-compact 12" Active Slim Subwoofer packs a serious punch and is ideal for adding bass to applications where space is limited. It is perfect for Vans, Wagons, Utes, and Hatchbacks. Designed for under/behind seat applications, this ultra-slim sub will give you the profound bass depth into the most minor place. General Features: 12" 4-ohm VPAS Series Subwoofer Power Handling: Peak: 600 watts RMS: 250 watts Slim design allows placement under a vehicle seat High output slim profile subwoofer Phase inversion switch: 0 or 180 degrees Cast aluminum enclosure RCA high-level inputs Low pass filter: 85 - 150Hz Subsonic filter: 30Hz Frequency response: 30 - 150Hz Vega Bass boost: 0 - 12dB Input sensitivity: High level: .9 - 12V Low level: .3 - 5V Wired bass knob included Fuse Rating: 25A x 1 8 gauge power and ground wiring is recommended for installation. Dimensions: 13.5"W x 11.25"L x 3"H Authorized Internet Dealer 1-year Manufacturer's Warranty Warning:This product can expose you to, known to the State of California, to cause cancer. For more information, go to P65Warnings.ca.

ABSOLUTE U.S.A TOYK972S Silver Dash Kit & TWH-950 for 05-11 Toyota Tacoma Interchange Dash Part: Metra 99-8214TG, Scosche TA2053B, American Intl TOY-K972SInterchange Harness Part: Metra 70-1761, Scosche TA02B, American Intl TWH-950Dash Kit Features: Single Double DIN Installation Dash Kit/ ISO Radios Compatible With 2005-2011 Toyota Tacoma Specially Design Patent Pending Side Mount Brackets Designed For Double DIN, (2) Single DIN Or DIN W/ Pocket Comes With A Storage Pocket Below The Radio Designed And Contoured To Match Factory Dashboard Showing A Gapless Fit Between The Dash And The Kit Painted To Match Factory Dash Color High-Grade ABS Plastic Structure Factory Style Texture All Necessary Hardware Included Illustrated Instructions For Easy Installation Color: Silver Kit Includes: Radio Housing ISO Brackets Trim Plate Pocket Harness Features: Plug-Into Radio Wiring Harness One 10-Pin Female Plug And One 6-Pin Female Plug Plugs Into OEM Radio Provides Power And 4 Speakers Heat Resistant For Lasting A Lifetime Allows Installation Of Aftermarket Radio Using Factory Wiring And Connector High-Quality ABS Plastic Molded Connector For The Perfect Fit Pre-Stripped To Make Installation Quick And Easy No Cutting Of Factory Wiring Needed Compatibility Vehicles:Toyota: 2005-2011 Tacoma Authorized Internet DealerNote:*** NOT FOR JBL OR FACTORY AMPLIFIED VEHICLES *** *** For Vehicles with Silver Dash*** The vehicle Compatability Chart May Vary Depending On Vehicle Options, Production Dates, And Install Applications. Please Inquire Before Purchasing.The wiring Harness Is NOT Compatible With Premium JBL, BOSE, Or Amplified Sound Systems. Warning:This product can expose you to, known to the State of California to cause cancer. For more information, go to P65Warnings.ca.